Choose rims by checking the wheel diameter, width, bolt pattern, offset, centre bore and load rating required for your vehicle. Then confirm tyre compatibility, brake clearance and mounting hardware. This guide helps you gather the details and compare wheels before ordering.
1. Start with your exact vehicle details
\n
Note the make, model, generation, year and engine version. Include all-wheel drive, an upgraded brake package or modified suspension where relevant. Different versions of the same model can have different wheel requirements.
\n
Check the vehicle manufacturer's wheel and tyre specifications in the owner's manual or documentation for your particular car. A tyre information label may also be inside a door opening or the fuel filler flap. Markings on the currently fitted tyres and wheels are useful for comparison, but they do not prove that a previous owner chose the correct setup.
\n
If the specifications are unclear, have your VIN and photographs of the existing markings ready so the vehicle version can be identified. Manufacturer-approved sizes are the starting point. Michelin explains approved size options.
\n\n
2. Compare the complete wheel specification
\n
“18-inch rims” is not enough information to choose a set. Compare the full specification and check the particular wheel against your vehicle version.
\n
\n\n\n\n\n\n\n
| Specification | What it means | What to check |
|---|---|---|
| Diameter, for example 18″ | The wheel diameter at the tyre mounting surface. | Compatibility with the tyre and the approved vehicle setup. |
| Width, for example 8J | 8 is the width in inches; J identifies the flange profile. | The tyre manufacturer's permitted rim-width range and space inside the wheel arch. |
| Bolt pattern or PCD, for example 5×112 | Five mounting holes on a circle with a 112 mm diameter. | An exact match to the vehicle's mounting pattern. |
| Offset, for example ET35 | The distance in millimetres between the wheel centreline and its mounting face. | Position relative to the suspension, brakes and bodywork. |
| Centre bore, CB or DIA | The diameter of the opening in the centre of the wheel. | Compatibility with the hub and an appropriate centring ring if specified. |
| Wheel load rating | The manufacturer's load limit for one wheel. | Suitability for the vehicle's load requirements. |
\n
See Compomotive's technical information and KMC's wheel specification guide for these terms.
\n
Example: 8J×18, 5×112, ET35, CB66.6
\n
This describes an 8-inch-wide, 18-inch-diameter wheel with five mounting holes, a 112 mm PCD, 35 mm offset and a 66.6 mm centre bore. It illustrates the markings; it is not a recommendation for a particular vehicle.
\n
For two wheels of equal width, changing from ET45 to ET35 moves the wheel 10 mm further outwards. If the width also changes, both the inner and outer positions need to be recalculated. There is no universal safe offset difference for every car.
\n\n
3. Choose the wheel size together with the tyres
\n
Decide whether you will keep your current tyres or buy a complete new set. Existing tyres must match the wheel diameter and be approved for its width.
\n
Moving to a larger wheel while keeping a similar overall tyre diameter usually means using a shorter tyre sidewall. This can make the ride feel firmer on uneven roads. For everyday use, compare approved combinations for comfort and total cost as well as appearance. Michelin explains tyre profile and markings.
\n
Include tyres, fitting, balancing and any required mounting hardware in your budget. If your car uses wheel-mounted tyre-pressure sensors, check their compatibility too. This lets you compare complete setups rather than the price of a single rim.
\n\n
4. Check brake clearance, load rating and mounting hardware
\n
A matching diameter and bolt pattern do not guarantee fitment. The spokes and inner wheel barrel must leave enough space for the brake calipers. Pay particular attention to performance brakes or modified suspension. Tire Rack explains the checks used to assess wheel fitment.
\n
The wheel load rating must meet the vehicle's requirements, taking its permitted axle loads into account. Dividing the car's unladen weight by four is not enough. Load rating also matters for heavier SUVs and electric vehicles.
\n
Wheel bolts or nuts must have the correct seat shape, thread and required length for the new wheels. A centring ring does not change the bolt pattern or offset. Where rings or other accessories are needed, confirm the mounting arrangement specified for that wheel. Tire Rack's technical FAQ also covers hardware and TPMS questions.
\n\n
5. Check these points before ordering
\n
- \n
- Vehicle: exact version, year, brakes and any modifications. \n
- Wheels: diameter, width, bolt pattern, offset, centre bore and load rating. \n
- Tyres: a size suitable for the wheels, with load and speed ratings meeting the vehicle's requirements. \n
- Fitting: brake and suspension clearance, hardware, centring rings and TPMS where required. \n
- Complete set: the correct quantity and separate front and rear sizes if the vehicle uses them. \n
\n
If any point is unresolved, clarify it before placing the order.
\n\n
Common questions about choosing rims
\n
Do all 5×112 wheels fit the same cars?
\n
No. The bolt pattern is only one specification. The remaining dimensions, load rating and mounting requirements must also be suitable.
\n
What does R18 mean on a tyre?
\n
R identifies radial tyre construction. 18 is the wheel diameter in inches that the tyre is designed to fit. It does not mean an 18-inch radius.
\n
Is it enough that the wheel fits onto the hub?
\n
No. Hardware, clearances and load requirements still need checking. After fitting, the wheel must clear the bodywork and suspension when steering too. The BBS installation manual highlights this check.
\n\n
Find rims for your car at KAWORK
\n
Browse the wheel range and save links to the models you like. For help with your choice, send KAWORK a question with your vehicle details, current tyre size and preferred wheel diameter.
\n
Once you have selected your wheels, use “Request a quotation” on the product page to add them to your quotation request.